Dissertation > Excellent graduate degree dissertation topics show

Study on Squeeze Casting Process of 7075 Aluminum Alloy Hollow Axle Body of Transmission Shaft

Author: HuangZaiGao
Tutor: ChenGang
School: Hunan University
Course: Materials Processing Engineering
Keywords: Squeeze casting Hollow transmission shaft 7075 Aluminum alloy Lightweight train
CLC: TG249.2
Type: Master's thesis
Year: 2009
Downloads: 113
Quote: 0
Read: Download Dissertation

Abstract


As an important parts of train bogie, transmission hollow shaft prepared by subsitituing low density aluminum alloy for steel, can reduce the weight of unsprung, improve transmission performance and promote the development of high-speed train. We examined ultra-high strength 7075 aluminum alloy,using squeeze casting method to prepare hollow shaft of reduction ratio, in order to provide reference for the development of aluminum alloy hollow shaft.The process parameters(squeeze casting pressure, pouring temperature, molding temperature) of squeeze casting and effects of heat treatment process were studied. The results are summarized below:(1) With the increase of casting pressure,microstructure of the samples become much finer. Microstructure under different pressures contained dendritic, granular and rose-shaped structure.solidification under prussure also reduce porosity, rarefaction and so on.(2) Low pouring temperature results in defects of misrun on the surface of casting, while high pouring temperature coarsen the microstructure. Low or high pouring temperature were both reduce density and mechanical property of the samples. The optimum pouring temperature range was about 680℃~700℃. A higher molding temperature also coarsen microstructure and reduce mechanical property of the samples. Experimental results indicates that the appropriate temperature of casting mold was around 250℃.(3) Under the experimental conditions, when casting pressure is 160MPa, the melt temperature is 700℃and mold temperature is 250℃, tensile strength and elongation of aluminum alloy hollow shaft specimen after heat treatment can reach to 545MPa and 8%, respectively.

Related Dissertations

  1. Filling copper alloy mechanical properties of bimetallic piston pump,TH322
  2. Microstructure Control and Properties of in Situ Fabricating Particulate Reinforced Aluminum Matrix Composites,TB331
  3. Development of a Control System of the Squeeze Casting Unit for Mg Wheel Production,TG233.1
  4. The Study on Indirect Squeeze Casting of the Larger-diameter Retainer,TG249.2
  5. Two dynamic loading conditions on the self-organization of 7075 aluminum alloy in shear zones injury,TG115.5
  6. Research on Squeeze Casting Technology for High Strength and Toughness Aluminum Alloy Parts,TG249.2
  7. Study on Squeeze Processing of ZA Alloy Casting with High Ratio of Height to Thickness,TG249.2
  8. Study on the Process Parameters and Solidification Behavior of Squeeze-cast Mg-Nd(-Zr) Alloy,TG249.2
  9. Study on Special Purpose Coating of Squeeze Casting of Iron and Steel,TG249.2
  10. The Research on Biparting Surface Mold Structure of Squeeze Casting,TG233.1
  11. Study on Prepartion and Properties of Sn-Bi Thermal Fuse,TG379
  12. Study on the Mould Design and Forming Experiment of Squeeze Casting Hammerhead Used on Hammer Crusher,TG315.2
  13. Die Cast Dies Design for Semi-solid Rheo-Extrusion Technique and Study on the Process Properties of Gear of Tachometer,TG376
  14. Study on HVAF WC Coating Sprayed at Aluminum Substrate,TG174.4
  15. The Research and Realization on the Mould Standard-part Library of Squeeing Casting,TP311.13
  16. (Al3Zr+Al2O3)p/A356 Composites’ Structure and Performance in Different Electromagnetic Field and Casting Technics,TG249
  17. The Study on the Numerical Simulation of Squeeze Casting,TG249.2
  18. Dynamic Simulation Design of Squeeze Casting Mold Based on Virtual Reality,TG249.2
  19. Semi-solid forming hypereutectic Al-Si alloy high-temperature performance,TG249.2
  20. Research on Mechanical Properties and Friction and Wear Properties of Squeeze Casting Zinc-Aluminium,TG249.2

CLC: > Industrial Technology > Metallurgy and Metal Craft > Casting > Special Casting > Pressure die casting
© 2012 www.DissertationTopic.Net  Mobile