Dissertation > Excellent graduate degree dissertation topics show

Study on Preparation of high-performance -doped lanthanum lead zirconate titanate piezoelectric ceramics

Author: WeiWei
Tutor: YaoPingPing;LuoFengHua
School: Central South University
Course: Powder Materials Science and Engineering
Keywords: piezoelectric ceramics Mechanical alloying MPB tiny powders sintering temperature
CLC: TQ174.6
Type: Master's thesis
Year: 2009
Downloads: 27
Quote: 0
Read: Download Dissertation

Abstract


As an intellectualized materials, PLZT piezoelectric ceramics were applied to many fields and own mang excellent performances such as piezoelectic, thermoelectic and photoeletric performances, this text introduce Mechanical alloying into the manufacture process of ceramic powders to obtain tiny powders which have excellent sintering behavior and were used to fabricate microlithic ceramics, microlithic ceramics have stronger bresking tenacity and longer life span.The influence of balling velocity and balling time on performaces of powders, dielectric and piezoelectric performances, the influence of the ratio of Zr to Ti and sintering temperature on composition of phase, dielectric and piezoelectric performances were important proportion of this text.The results illuminate that the velocity of reaction between atoms is higher when balling velocity is improved. The sintering property of powders can be improved when the balling time was delaied. However, it will decrease if the balling time is too long.The ceramics are near by the MPB if 0.66≤Zr/Ti≤0.64, and if Zr/Ti is 65/35, they have excellent properties such as:p=7.64g/cm3εr=182, d33= 136.8pc/N,Kp=0.284.When the sinterng temperature between 1000℃and 1200℃, the ceramics all are PLZT phase, The grain boundary is clear and the average size of gain is less than 1μm. whereas the ceramics have ZrO2 phase besides PLZT phase, the size of grain has slim increase and the grain boundary become intangibly when sintering temperature is 1250℃. The density and hardness of samples firstly increases and afterward decreases alongwith the improved temperature, the maximal value of them respectively is 7.64g/cm3 and HV585.7. at the same time, the d33 of ceramic also achieves the maximal value that is 136.8pc/N.The best value of balling velocity, balling time, Zr/Ti and sintering temperature respectively is 400rpm,12h,65/35 and 1100℃.

Related Dissertations

  1. Study on Low Temperature Sintered PSN-PZT Piezoelectric Ceramics,TM282
  2. Synthesis of Ag / Al 2 O 3 powder composites research,TB383.3
  3. Magnesium slag , red mud ceramic filter balls resource utilization Experimental Study of As removal from wastewater,X703
  4. WCu electrical contact products injection molding process and performance studies,TF124.3
  5. Research of Micro-feed Control Strategy Based on Micro-EDM,TG661
  6. Preparation and Properties of Li+ Doped KNN and Ba2+ Doped BNT Composite Ceramics,TM282
  7. Study on Microstructure Properties and Deformation Behavior at High Temperature of Al-Pb Alloy,TF124.5
  8. TiAl Alloys SPS sintering of Microstructure and High Temperature Oxidation,TF124.5
  9. Preparation of Nonstoichiometric CrN_x by Ma and Its Sintering Characteristric,TF124.5
  10. The Design of Tool Wear Compensation System Based on Piezoelectric Actuator,TG71
  11. Study on the Preparation of Nitride in High Magnetic Field and by Mechanical Alloying,TG156.82
  12. The Research of Biological Ceramics Producing with Cotton Stalks,TQ174.1
  13. Study on Ceramic Material of MgTiO3-CaTiO3 System in High Frequency,TQ174.1
  14. Research on the Properties of the PZT Piezoelectric Ceramics Doped with Antimony and Lithium and the Optimization of Process,TM282
  15. The Study of Piezoelectric Properties on BaTiO3 Based Lead-free Piezoelectric Ceramics,TM282
  16. Preparation, Enhancement and Toughening of PBSZT Piezoelectric Ceramics,TM282
  17. Research on Characteristics of Sintered Body Mixed with Sewage Sludge,TU528.0
  18. TiB_2, TiAl and TiC nano- powders prepared by mechanical alloying of,TB383.1
  19. Preparation and Modification of K0.5 Na0.5 NbO3-based Lead-free Piezoelectric Ceramics,TM282
  20. Influence of CuO Additive, TiO2 Raw Material and Preparing Techniques on Physical Properties of BaTiO3 Piezoelectric Ceramics,TM282

CLC: > Industrial Technology > Chemical Industry > Silicate > Ceramic Industry > Production process and equipment
© 2012 www.DissertationTopic.Net  Mobile