Dissertation > Excellent graduate degree dissertation topics show

The Experimental Investigation and Nonlinear Finite Element Analysis of Z-Shaped Column’s Shearing Performance Subjected to Low-Cyclic Horizongtal Load

Author: JiQing
Tutor: YangJunJie
School: Zhejiang University of Technology
Course: Structural Engineering
Keywords: low cyclic Z-shaped cross section column experimental investigation shear failure failure mode shear-resistant capacity axial compression ratio ratio of section height stirrup reinforcement ratio finite-element analysis
CLC: TU375.3
Type: Master's thesis
Year: 2010
Downloads: 32
Quote: 0
Read: Download Dissertation

Abstract


Z-shaped column is widely used in the structure of residential architecture in china, but currently, researches on Z-shaped column are insufficient, and correlative conclusions are absent. Therefore, there is no unified design method in engineering field. Based on the experiment study and theoretical analysis of Z-shaped column under the load which is horizontal to the flange, this dissertation reveals shear failure mechanism and discipline of Z-shaped column for us. It also provides us with the design method which can be used in practical engineering.Firstly, the shear-resistant carrying capacity experiment of Z-shaped column was carried out, through the synthetic analysis on both crack expanding condition and failure modes, the shear failure mechanism and shear failure discipline are studied, the ductility discrepancy between Z-shaped column and other specially shaped columns and between Z-shaped column and rectangular-shaped column was obtained, the factors such as: axial compression ratio, stirrup reinforcement ratio and ratio of section height to section thickness of column 1eg,which affect the shear-resistant carrying capacity of Z-shaped column, was preliminary analyzed. Secondly, based on the results of experiment, the nonlinear finite element calculation was carried out, a further study was accomplished on the effect of those influential parameters which contained axial compression ratio, stirrup reinforcement ratio and shear span ratio. Conclusions can be drawn as following: compression-shear failure, shear-bending failure、bending failure were three main failure modes of Z-shaped column, the most important factor which affected failure mode and ductility capacity was shear span ratio, flange provided most part of shearing-resistant carrying capacity when Z-shaped column subjected to the load horizontal to the flange. Lastly, the calculation method about shear-resistant carrying capacity was studied according to the experiment results and finite element numerical simulation results. The regression formula from the experiment and numerical simulation results、and the design formula were obtained. Some suggestions respect to practical engineering were presented for the reference of structure designer.

Related Dissertations

  1. Research on the Mainframe System of Powder Mixed EDM and the Craft Experiment,TG661
  2. EDM Electrode Wear Mechanism and Control Research,TG661
  3. Finite Element Analysis and Structure Optimal Design for Combined Seal at Normal Temperature and Low Temperature,TH136
  4. Key Technologies of Dam-break Life Loss Risk Assessment Research,TV122.4
  5. Study on the Design and Biomechanical Behaviors of Individualized Artificial Knee Joint,R318.1
  6. Design of Testing Equipment for Electronic Products,TN06
  7. Multi-pin Internal Fixation of Calcaneal Fractures in Finite Element Analysis,R687.3
  8. Airborne radar antenna pedestal rapid design systems research and development,TN959.73
  9. Sham hose drum drive means and hydraulic system of the structure,TE973
  10. The magnetorheological damper mechanical properties and Gun Recoil,TB535.1
  11. Nonlinear Structural Dynamics Analysis and Optimization Design on Naval Gun Driver,TJ391
  12. Design and Analysis of Automatic Steel Pipes Butt Tool,U673.38
  13. Analysis on Unloading of Large Span Steel Structures and Research on Its Mechanical Analysis,TU391
  14. Simulation of the Clinching Process Using FEA Method with Steel and Aluminum Alloy Sheets for Automotive Sunroof Frame,U463.83
  15. M1 of CRH2-300 Train Finite Element Analysis and Travelling Comfort,U266
  16. The Design of Telescopic Asphalt Spraying System,U415.524
  17. Development of Post-process System in Sheet Metal Simulation Based on SolidWorks,TP391.72
  18. Failure Analysis and Structural Optimization of the Typical Fine Blanking Punch,TG385.2
  19. The Structure Design of 2000kN Servo Press for Hot Forming,TG385
  20. Al Wire Bonding Failure and Automatic Optical Inspection on Power Device Leadframe,TG441
  21. Simulation Analysis and Experimental Study on Hysteretic Behavior of High-performance Shear Panel Damper,TU352.1

CLC: > Industrial Technology > Building Science > Building structure > Concrete structure,reinforced concrete structure > Reinforced concrete structures > Column
© 2012 www.DissertationTopic.Net  Mobile