Dissertation > Excellent graduate degree dissertation topics show

Study on Laser Processing and Machining of CVD Diamond Thick-Film

Author: XuFeng
Tutor: WangZuo；ZuoDunWen
School: Nanjing University of Aeronautics and Astronautics
Course: Mechanical Manufacturing and Automation
Keywords: CVD diamond thick-film Laser Polishing Cutting Mechanical polishing
CLC: TB43
Type: Master's thesis
Year: 2002
Downloads: 393
Quote: 6
Read: Download Dissertation

Abstract


ABSTRACTAs a good material in engineering, diamond can be used in many fields. However, natural diamond is scale and expensive, so people make synthetic one using chemical vapor deposition (CVD). But polycrystalline CVD diamond films have rough and non-uniform thickness which can adversely affect their application. Furthermore, it is difficulty to machining the CVD diamond thick-film.In this paper, the studies on the machining of CVD diamond thick-film were carried out. Laser processing and mechanical polishing are used to machining the CVD diamond thick-film. The major research work is included as follows:1. Studies on mechanism of the laser processing the diamond were carried out. The laser heats up the diamond and causes the temperature rises on the surface of diamond film. At the different temperature, the different physical and chemic change will happen. The rules of the laser ablating diamond were researched by experiment.2. On the basic of theory, experimental studies on laser cutting and polishing diamond film were carried out. In this paper, Q switch Nd:YAG laser was used to polishing the diamond films. The incidence angle of laser beam and other factors have been found to result in more effective polishing, with optimal best smoothing observed at incident angles of 75 ? . The electron microscope and Raman spectra were used to analyze the diamond films after laser processing.3. Experimental studies on mechanical polishing diamond film were carried out. The primary investigation was carried out using mechanical polishing equipment. The diamond films after polishing were observed by means of scanning electron microscope. The machining process and the factors which influence the polishing efficiency and quality were preliminary discussed.

Related Dissertations

  1. Research on Welding Characteristics of CO2 Laser-GMA Hybrid Welding for Ultra-Low Carbon Bainitic Steel,TG456.7
  2. Research on Synchronous Acquisition and Processing System Detecting Defocus Signal Based on DSP,TH741
  3. Design and Fault Diagnosis of the Coarse Pointing Control System in Satellite Laser Communication,V443.1
  4. Characterization and Identification of Maturity of Pig Manure Composting,S141.4
  5. The Correlation between the Intraocular Lens Power and the Myopia before and after Excimer Laser Surgery,R779.63
  6. Electron Acceleration by Intense Laser in Vacuum,TN241
  7. Visual Quality Assessment between Different Ways Assisted Customized LASIK by OQAS,R779.63
  8. Erbium-doped fiber amplifier pump laser drive source research applications,TN248
  9. \,G633.955
  10. Raindrop characteristics and signal transmission of the laser,P412.22
  11. Development of Timing Sync Circuit of Photo-cathode Rf Gun and Research on Application Possibility of Radically Polarized Laser,TL503.3
  12. Experiment Research and Temperature Distribution Simulation of Thermoplastics in Laser Transmission Welding,TQ320.1
  13. The Processing Research of Metal Electrohemical Wire-cutting,TG48
  14. Research on the Technology of Online Detecting for Weld Defects of Strip Steel,TG441.7
  15. Research of Five Axis Milling Cutting Force Signal Processing,TN911.7
  16. Study on the Output Characteristic of High Power Long-Pluse Solid-State Laser,TN248
  17. Preliminary Exploration of the Refractive Index and Sbs for Pulse CO2 Laser Effect on Cross-critical Fluid,O437.2
  18. Coupled Optical Design Used for Nd:YVO4 Laser End-pumped by a Laser Diode,TN248
  19. Research of Spectral Beam Combining Technology for High Power Fiber Lasers,TN248
  20. Study on the Laser Characteristic of Tm3+-doped Double-cladding Fiber,TN248
  21. Experimental Study of High Harmonic Generation from Inert Gas Using Femtosecond Laser,O437

CLC: > Industrial Technology > General industrial technology > Industrial common technology and equipment > Thin-film technology
© 2012 www.DissertationTopic.Net  Mobile