Dissertation > Excellent graduate degree dissertation topics show

Research and Simulation on Vehicle’s 4 Wheel Drive System

Author: QiLie
Tutor: LvXinMin
School: Northwest University of Science and Technology
Course: Mechanical Design and Theory
Keywords: vehicle 4WD ADAMS control system simulation
CLC: U464
Type: Master's thesis
Year: 2011
Downloads: 194
Quote: 1
Read: Download Dissertation

Abstract


With the development of 4WD technology, some high-performance cars and sports cars began to use 4WD drive system in order to improve their dynamic property and stability. Nowadays, designers have considered 4WD drive system as a part of vehicle control, and they tired to distribute the drive torque to the wheel tires as far as reasonable, according to vehicle driving conditions and road conditions. The force of driving wheel should be changed with the road conditions and drivers’intent so as to improve performances of vehicles. This paper analyzed the characteristics of 4WD and the principles of power distribution, and established a simulation model and control system, under the following steps:First, build a vehicle simulation model in ADAMS, including: chassis model, steering model, the front suspension model, the inclined rear suspension model, tire and road model, and get better results by debugging.Second, establish the principle of power distribution of 4WD; count the distribution ratio via the equation when the car was linear accelerating, climbing and cornering.Third, Two-wheeled vehicle model and four-wheeled vehicle model were established when the car was doing uniform circular motion, analyze the affect of yawing moment on stability factor (K) and turning radius(R). At the same time analyze the singular point in the differential equations about the car was turning; find the stable point when the car was at different speeds and different steering angle.Fourth, analyze the constraints when the car was running; establish constraint equation to get the optimal power distribution. Finally compare the theoretical result with the simulation in ADAMSFifth step is establishing control systems in Simulink, and co-simulation with ADAMS so as to prove the superiority of full-time 4WD by comparing to RWD. Analysis the longitudinal slip rate of each wheel by setting the front and rear load to mimic conditions on the ground. Each wheel longitudinal slip rate change not affect each other, only relevant on vertical load and the driving force when without control system, so the dynamic has not been fully exploited. By adding control system, the longitudinal slip rate of each wheel to maintain the same, show the control system will allocate the power to each wheel reasonable.The results show that the method of analyze the vehicle stability by a mathematical model a better way, simulation model established by Adams will be accurate than by MATLAB, but the control system will be established easily by MATLAB, this paper design a power distribution way by co-simulation.

Related Dissertations

  1. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  2. Design of Reciprocatingwire Outfit of Mwedmand Research on It’s Control System,TG484
  3. Study on Springback of High-Strength Steel Stamping,TG386
  4. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  5. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  6. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  7. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  8. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  9. Single Neuron PID Control for Electro-Hydraulic Servo Unit of Ship Rudder,U666.152
  10. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  11. Numerical Simulation of Biomass Direct Reburning,TK16
  12. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  13. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  14. Study on Gas-Solid Two-Phase Flow in Spouted Beds,TK173
  15. Experimental Study and Numerical Simulation on Aerodynamic Field of Tangential Bias Swirl Burner,TK223.23
  16. Characteristic Study of Combustion in Central Reverse Flame Chamber,TK223.21
  17. Numerical Simulation and Contrastive Analysis of Labyrinth Seals and Leaf Seals,TK263.2
  18. Simulation Research on Compound-Structure Permanent-Magnet Synchronous Machine System Used in Hybrid Electric Vehicles,TM341
  19. Research on an Axial/Radial-Axial Flux Compound-Structure Permanent-Magnet Synchronous Machine Used for Hybrid Electric Vehicle,TM341
  20. A Simulation Study of the Effects of Ischemia to Spiral Waves in 2-D Human Ventricular Tissue,R318.0
  21. Research of Predictive Control in Water Treatment Plant Based on Neuron Network,TP273.1

CLC: > Transportation > Road transport > Automotive Engineering > Automotive engine
© 2012 www.DissertationTopic.Net  Mobile