Dissertation > Excellent graduate degree dissertation topics show

Research on Power Factor Correction Technology and Its Controller Chip Design

Author: LiKai
Tutor: WuXiaoBo
School: Zhejiang University
Course: Circuits and Systems
Keywords: Power Factor Correction(PFC) Power Factor Pre-regulator(PFP) Average Current Mode Control Input Voltage Feed-Forward Chip
CLC: TN86
Type: Master's thesis
Year: 2006
Downloads: 639
Quote: 10
Read: Download Dissertation

Abstract


With the rapid development of power electronics, the capability of utilizing electricity and the performances of electric network have been greatly improved. But due to wide applications of the rectifiers, various harmonic waves are produced. They pollute the electric network seriously and reduce the efficiency of production, transmission and utilization of electricity. Recently, the energy shortage has become the bottle neck of developing national economy. Since the power factor is of key importance to raising of energy efficiency and improving of performances of the electric network, new rectifiers with high performance are in dire need, which have the power factor correction function to restrain the harmonic waves of switch power supplies.Research on the power factor correction technology in switch power supplies is internationally focused on the circuit topology and the control circuit. In recent years the power factor correction technology are developed rapidly, which have become an important field of power management IC. Now the power factor of modern switch power supplies with power factor correction function can be raised to 0.95~0.99, near unit. Compared to the technology progress overseas, the research on power factor correction IC (integrated circuit) in our country is just started up. It is partly due to the restriction of the domestic IC process required for these IC. The requirements of high voltage and large driving capacity made it difficult to develop these.In this thesis, the recent power factor correction technologies were widely disscused. And the enhancement of power factor pre-regulator (PFP) system was introduced by improving the average current mode control. An input voltage feed-forward part was added to the control loops to improve the system stability while the input voltage varied. For the use of active power factor correction technology of modern power electronic appliances, a controller chip was proposed based on the BCD (Bipolar-CMOS-DMOS) process with an average current mode control and a feed forward voltage. The whole design was fulfilled including system design, circuit module design and layout design. A solution using macro model was introduced to settle the difficulties in system simulation of high frequency switch power supplies. A 250W Boost converter circuitry based on the chip was simulated. The results showed that the THD (Total Harmonic Distortion) of its output current was reduced to 1.7% and the near unity power factor was available, when the input voltage is 220V, 50Hz. Soft start up and the protection functions including the under and over voltage protection and the over current limit were realized perfectly. And the power dissipation is 0.11W (including switching loss) when supply voltage is 12V. The designed chip was taped out. As results, the thesis gave the detailed testing results, which show that the chip works normally and the specifications meet the designed Spec. well.

Related Dissertations

  1. The Research and Realization of Multi-Carrier Modulation Method Based on the Low-Frequency Elastic Wave Channel,TN919.3
  2. Microfluidics pulse drive - control microarray spotting system design and experimental study,TN402
  3. Design of Fully Integrated On-chip LC VCO,TN752
  4. Micro- array filter connector plate moments chip design,TN402
  5. Spatio-Temporal Data Prefetching,TP333
  6. The Intelligent Reactive Power Compensation Based on MCS-51,TP368.12
  7. Research on Single-stage PFC Based Onactive Clamp Forward Converter,TM46
  8. Research on Soft-switching PFC Based on Single-state Flyback Converter,TM46
  9. Study on the Dry Cutting Performance of Austenitic Stainless Steel 0Cr18Ni9,TG142.71
  10. The Simulation and Numerical Analysis about Manufacture Processing of Stainless Steel Based on ABAQUS,TG501
  11. Design and Investigation on Insulated Gate Bipolar Transistor,TN322.8
  12. Research on a Zero-Current Soft Switching for PFC Converter,TM461.5
  13. A Compact Realtime Turbidity Measuring System for Loop-mediated Isothermal Amplificationon Microfluidic Chip,TN492
  14. Electromechanical Co-simulation and Experimental Verification for Swing Arm of High-Speed LED Chip Sorting Machine,TN405
  15. Based on active infrared and ultrasound scan flip-chip Defects Detection,TN407
  16. A Low Power Power Management System for Passive RFID Tag Chip,TN402
  17. Digital T / R module transceiver front-end design and research,TN957
  18. Research and Design of a Low Dropout Linear Regulator,TM44
  19. The Studies of Brushless Motor System Design in Antenna Turntable Axis,TM33
  20. Failure Analysis and Processing Technology Improvement of the Bicycle Flywheel Parts and Its Molding Die,U484
  21. CMOS image sensor parallel test development,TP212

CLC: > Industrial Technology > Radio electronics, telecommunications technology > Radio equipment,telecommunications equipment > Power supply
© 2012 www.DissertationTopic.Net  Mobile