Dissertation > Excellent graduate degree dissertation topics show

Numerical Simulation of Reversible Axial Turbine

Author: GengZaiMing
Tutor: ZhengYuan；PanHuaChen
School: Hohai University
Course: Water Resources and Hydropower Engineering
Keywords: Two Directions Reversible Axial Turbine Numerical Simulation efficiency Flow Pattern Hydraulic Loss
CLC: TV734.1
Type: Master's thesis
Year: 2006
Downloads: 261
Quote: 5
Read: Download Dissertation

Abstract


Accurate Simulation of flow field in hydraulic machinery helps us to predict general performance of different components (especially that of runner) with low cost. So it is becoming an essential tool for designing new high quality runner in factories. People have been looking for good methods which can work well in a wide operation range to precisely predict comprehensive performance of hydro unit, including efficiency, cavitation property and stability, so as to reduce cost in test and model-making.In this thesis, some theoretical problems relating to numerical simulation of hydraulic machinery were put forwards firstly. Combing with standard k-e model, N-S equations were employed in three dimensional steady flow calculation under many work conditions with different blade angle and different guide vane openings. In the simulation, plenty of methods have been used, including structural grid division, velocity input of the turbine inlet boundary condition, free outflow in outlet, static and dynamic interfering sliding grid model technique in fixed coordinates and rotational coordinates, wall function applied in along-wall and SIMPEC algorithm which had good convergence for pressure and velocity.From the calculation,turbine efficiencies have been obtained that it was 75.8% of most high-efficiency in the positive operation condition,and 66.6% in the negative operation condition.The results from the calculation agree well with the results from the experiment,but the value of calculation was lower than the value of experiment,that the average error was 7.5% in the positive operation condition and 2.5% in the negative operation conditon.The error analysis was performed at the same time.Based on work mentioned above, further analysis on inner flow characteristics of turbine have been studied in the positive and negative condition. According to small blade angle blade velocity of flow and pressure maldistribution, and to take off to flow and bump in the too big blade angle condition the losses increased in various degree.Using the numerical simulation results, component loss in different work conditions has been calculated.The losses wave relatively high in therunner and draft tube.The section of losses of runner was about 15% in the positive condition,but about 21% in the negative condition.The losses of draft tube was about 12% in the positive and negative condition.The kinetic losses of draft tube attained 19% because the kinetic energy of the runner outlet increased and the kinetic resumed coefficient of draft tube was small at the large discharge condition deviating from the negative optimum operation condition.

Related Dissertations

  1. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  2. Study on Springback of High-Strength Steel Stamping,TG386
  3. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  4. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  5. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  6. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  7. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  8. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  9. Numerical Simulation of SNCR Process of a 600MW Utility Boiler,TK222
  10. Numerical Simulation of Biomass Direct Reburning,TK16
  11. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  12. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  13. Study on Gas-Solid Two-Phase Flow in Spouted Beds,TK173
  14. Experimental Study and Numerical Simulation on Aerodynamic Field of Tangential Bias Swirl Burner,TK223.23
  15. Characteristic Study of Combustion in Central Reverse Flame Chamber,TK223.21
  16. Numerical Simulation and Contrastive Analysis of Labyrinth Seals and Leaf Seals,TK263.2
  17. Research on High Efficiency Interior Permanent Magnet Synchronous Motor,TM341
  18. A Study about the Stock Index Future’s Influence on the Stock Market,F224
  19. Yunnan Province, human capital, the network structure of critical efficiency factor,F249.27
  20. Numerical Study on Phosphorus Distribution in Water Environment of the Three Gorges Reservoir,X832
  21. The Design and Performance Simulation of External Valve Small Displacement Pump,TE933.3

CLC: > Industrial Technology > Hydraulic Engineering > Hydropower utilization of hydropower project > Hydropower station construction and equipment > Mechanical and Electrical Equipment > Turbine and its equipment
© 2012 www.DissertationTopic.Net  Mobile