Dissertation > Excellent graduate degree dissertation topics show

Analyzing of Injection Molding Steel Net Reinforced HDPE Ball Valve by CAE Software

Author: HuangJunDong
Tutor: QianXin；JinYangFu
School: Zhejiang University of Technology
Course: Materials Science
Keywords: steel net reinforced HDPE shrinkage deformation analysis insert molding
CLC: TQ320.662
Type: Master's thesis
Year: 2011
Downloads: 43
Quote: 0
Read: Download Dissertation

Abstract


As the HDPE pipe been widely used in the urban water supply and drainage, building water supply and drainage, city gas supply, agricultural irrigation and petrochemical fields, the demand of HDPE ball valve is increasing. In order to meet the requirement of installing and using, the thick wall and the steel-plastic composite way are often used to increase the strength and reduce creep. However, there are two problems involved in producing the steel-plastic composite reinforced HDPE ball valve: first, there is a big shrinkage in thick wall HDPE ball valve; second, if the steel skeletons are poorly designed, the deformation of steel skeleton likely to happen during the injection process. With the widely application of CAE technology, computer aided design has played an important role in product exploitation and design. It not only saves cost and time in exploitation, but also provides some reliable scientific basis.The subject, analyzed the influence of shrinkage in different molding parameter by using injection molding software Moldflow. Then, based on the coupling method between the Moldflow and ANSYS CAE, it simulated the deformation of ball valve during injection and optimized the steel’s diameter and structure.The results showed that:(1) There is an obvious relationship between the shrinkage of thick-walled ball valve and the injection molding conditions. During the holding pressure time, melt temperature and mold temperature are the main factors of shrinkage. The longer of holding pressure time is, the more obvious supplied-shrinkage effect shown. This made the shrinkage of product reduced. For core, melt temperature is the main influence factor. It can reduce shrinkage by keeping relatively low melt temperature. This demonstrated that heat shrinkage is the main effect for core. Mold temperature is the main impact factor for the surface layer shrinkage. Similarly, it can reduce shrinkage by keeping relatively low mold temperature. The optimized molding parameters by orthogonal experimental are: melt temperature 230℃, mold temperature 50℃, holding pressure 90%, holding pressure time 1500s.(2) According to the deformation analysis on ANSYS, the deformation of steel-net-insert is mainly related to diameter and structure of steel net. Comparing with the 3mm-diameter wire, the deformation of 5mm-diameter wire was reduced by 60%. But with the wire the further increase of diameter, the trend of deformation decreases slows down. Considered to the structure of steel net, vertical arrangement of 8 wires is an ideal structure; At this time, the largest deformation is 0.566mm. This structure can bring it into accord with using requirement of ball valve.

Related Dissertations

  1. Voice Signal De-noise Base on Wavelet and Arithmetic Implement with DSP,TN912.3
  2. Rock-fill Concrete Experiments on Comprehensive Properties and Studies on Thermal Stress,TU528
  3. The Experimental Research on Regeneration Aggregate and Proportioning of Recycled Concrete Brick,TU528
  4. Study on the Factors Which Influence the Pre-stressed Concrete Bridges Cracking and Down-warping,U448.35
  5. Study on Mechanical System Design of Weighty Payload and High Accuracy Antenna for Radar Satellite,V443.4
  6. Deformation Analysis and Prediction Based on Chaotic Time Series,N945.2
  7. V-shaped Piers of Continuous Rigid-Frame Bridge Static Analysis and Construction Control,U448.23
  8. Analysis of Deformation and Research on Construction Control for Large-span Continuous Rigid Frame Bridge,U445.4
  9. A Study of Deformation Analysis Method Based on Distance Image,TP391.41
  10. The Cenozoic Structural Formation and Hydrocarbon Distribution in Western Region, Qaidam Basin,P618.13
  11. Linear Control of Long-span Continuous Rigid Frame Bridge in Construction Stage,U445.4
  12. Underlying Shield Tunnel Deformation Effected by Pit Excavation,TU753
  13. The Research on the Swelling Deformation Law of Expansive Rock (Soil) in Luwangfen for the Midline of North Water Transfer Project,P642.1
  14. Research on A Suv Interior Booming Noise Analysis and Control,U467.493
  15. The Research of Concrete Shrinkage and Creep Experiment,TU528
  16. The Research on Arch Centering Cantilever Technology and Early Crakes of Concrete Arch Rib,U445.57
  17. Full-face Formwork Pre-camber Analysis and Design for Continuous Beam Bridge,U448.215
  18. Simulation Analysis of High Speed Railway Large Span Continuous Beam Bridge,U445.4
  19. Property Study on Shrinkage Compensating Concrete and Application,TU528
  20. Image De-noising Based on Wavelet Shrinkage,TP391.41
  21. Effects of Pore Solution on the Drying Shrinkage of Hardened Cement Pastes and Its Mechanism,TU528

CLC: > Industrial Technology > Chemical Industry > Synthetic resins and plastics industry > General issues > Production process and production technology > Forming > Injection molding
© 2012 www.DissertationTopic.Net  Mobile