Dissertation > Excellent graduate degree dissertation topics show

Research of Injection Unit and Ejection Unit Control Technology of All-electrical Injection Molding Machine

Author: XuYingPeng
Tutor: ZhouHuiCheng
School: Huazhong University of Science and Technology
Course: Mechanical and Electronic Engineering
Keywords: all-electrical injection molding machine control system state machine press packing metering
CLC: TQ320.5
Type: Master's thesis
Year: 2013
Downloads: 14
Quote: 0
Read: Download Dissertation

Abstract


All-electrical injection molding machine has advantages of energy-saving, highaccuracy, high speed and cleanliness. The control systems abroad of all-electrical injectionmolding machine have had advanced functions, such as current monitoring, on-line visualinspection, mold protection, synchronous temperature rise, quality informationmanage-ment and process optimization, etc. Limited by control system and servotechnology, domestic manufacturers rarely involves in all-electrical injection moldingmachine. Following the deep analysis of process requirements, the software and hardwareframework and the control technology of injection unit and ejection unit are completedbased on the platform of HNC8numerical control system.The similarity and distinguish between all-electrical injection molding machinecontrol system and machine tool NC system are analyzed according to the basic process ofinjection molding. State machine is applied to manage the processing action of each motorfor the differences where the former uses processing parameters and the later G-code todrive the machine. The state-machine is applied to manage the process action of eachmotor, using which the control arithmetic of injection and ejection unit is designed andrealized following building up of the model, state division and tidying of state transfercondition. Ladder program is used to monitor the operation panel and switch signal of themachine, to support the interlocking logical judgment and to send control commandsautomatically.Press packing model of injection unit is built up, and a method is supplied to achievethe following control of setting packing pressure, which combines PI controller andpressure acceleration planning, with a result of getting a rapid response to pressurepacking and resolving the problem of pressure overshoot. A method of direct backingpressure control based on conic is raised after the analysis of metering process and itsinfluencing factors, which resolves the problem that how to control the injection motor’srotation speed to following the setting back pressure and that can be resolved through theadjust of spring force of back pressure valve in the traditional hydraulic injection moldingmachine. Motion model of ejection motor is built up after the analysis of several ejectionmotion mode. Process control arithmetic of ejection motor using the thinking ofhierarchical structure and building block design is achieved. The function of pre-ejection,ejector lever protection and intelligent parameter optimization are also developed.A prototype machine is developed and principle experiments are completed on theplatform of a Chen Hsong injection molding machine. The back pressure can be controlledless than0.8MPa and the repeat accuracy can reach0.24%. The control system hasadvantages of manipulation, control precision, repetition accuracy and plasticizing effect,which satisfy the designing requirements.

Related Dissertations

  1. Design and Fault Diagnosis of the Coarse Pointing Control System in Satellite Laser Communication,V443.1
  2. Infrared Imaging Target Simulation Resistance Array Control System Development,TJ765.4
  3. Research on Attitude Control Law of Endo-Atmospheric Missile,TJ765.23
  4. Research on the Control and Remedy of Nanopositioning Stage Drived by Piezo Material Lead Zirconate Titanate,TP273
  5. Research on Control System and Head of 7-Axis NC Fiber Placement Machine,TG659
  6. Control System of Rotary Drying for Flake Agricultural Materials,S226.6
  7. Research and Application of the Oil Gas Water Measuring Technique Based on GLCC,TE33
  8. Hardware Implementation of Block Ciphers Algorithm Based on Petri Net,TN918.2
  9. Research and Design on Experimental Platform of Rubber Belt Joint Dynamic Durable,TH222
  10. Research and Design of DC Electricity Metering Equipment in Off-board Charger,U463.6
  11. Research on Key Technologies of Subsea Vertical Collet Cnonector,TM503.5
  12. Chinese and Uighur Group Financial Control,F406.72
  13. Brushless DC Motor and Control System,TM33
  14. The Design and FPGA Verification of Embedded UART Based on VHDL/FPGA,TN47
  15. The Kinematics and Dynamics on the Cross-rod Parallel Machine Tools,TH113
  16. Modelling and Development of Simulation Software of Rolling Mill Bending Roller Control System,TG334.9
  17. The Research of Coal Mine Drainage Automatic Control System,TP273
  18. The Design Research and Control Realization of One Kind of 4-DOF SCARA Robot,TP242
  19. The Research of Small Size Soccer Robot Control System Based on FPGA,TP242
  20. Research on DSP-based Control System of Hexpod Robot,TP242
  21. Research on Delay Compensation and Schedule Algorithms of Networked Control Systems,TP273

CLC: > Industrial Technology > Chemical Industry > Synthetic resins and plastics industry > General issues > Machinery and equipment
© 2012 www.DissertationTopic.Net  Mobile