Dissertation > Excellent graduate degree dissertation topics show

Structure Optimization and Insulation Properties of Plasma Sprayed At/Al2O3Composite Coating

Author: GuoRui
Tutor: LiangBo
School: Yanshan University
Course: Materials Engineering
Keywords: plasma spraying AT/Al2O3composite coating structure optimization insulation properties
CLC: TG174.4
Type: Master's thesis
Year: 2013
Downloads: 3
Quote: 0
Read: Download Dissertation

Abstract


In this dissertation, AT/Al2O3composite coatings with the Ni transition layer weredeposited on the Cu substrate by atmospheric plasma spraying （APS） using commercialNi-based alloy powder, AT （Al2O3-TiO2instead） composite powder and pure Al2O3powder as feedstock materials. Microstructure, phase composition, component distributionof composite coatings were characterized by scanning electron microscopy （SEM）, energydispersive spectrometer （EDS）, X-ray diffraction （XRD）, etc. The coating properties, suchas porosity, microhardness, fracture toughness, bond strength, DC breakdown voltage andresidual stresses, were measured. The microstructure and properties of four different ATcoatings were examined and compared. The stress distribution of Al2O3coating wasdiscussed and AT/Al2O3coating was optimized based on the analysis results of stressdistribution.The results show that AT20（Al2O3-20wt.%TiO2） coating demonstrates well bondingand dense microstructure. It is consisted by less γ-Al2O3phase content, relatively moreα-Al2O3and Rutile-TiO2phases. Tensile strength of AT20coatings is1.6times that ofAl2O3coatings. Its hardness value is83%that of Al2O3coating and the lifetime of itsbeginning crack is two times that of Al2O3coating. AT20coating was selected as themiddle layer to enhance the synthetical performances of AT/Al2O3composite coating.The surface stress of free-standing Al2O3coating is about168.3MPa, and the stress ofAl2O3coatings with Cu substrate is about28.5MPa. After optimizing, the thickness of Nilayer, AT20layer and Al2O3layer are75±5μm,185±20μm and265±15μm respectively.The bonding strength of optimized AT20/Al2O3coating is over15MPa.The dielectric mechanism investigation of Al2O3coating shows that breakdownmorphology of Al2O3coatings is typical corona breakdown morphology, the insulationmechanism can be explained by intrinsic insulation mechanism and the thermalmechanism. Moreover, the energy release rate during breakdown processes is obeyingGriffith rule. The dielectric properties of Al2O3coatings can be improved by both of thecoating thickness and sealing treatment, and the overlap of sealants can strongly reduce sensitivity to relative air humidity.Under the conditions of100Hz and25℃, the resistivity of optimized AT20/Al2O3coating is1.18×108·m, relative dielectric constant is1.25, dissipation factor is0.6andthe breakdown strength is about11.72±0.47KV/mm after the sealing treatment.

Related Dissertations

  1. The Research of Land-Use Optimization Approach Based on Non-Point Source Pollution Controlled,X24
  2. Chemical Construction Company Human Resource Management,F426.7
  3. Optimization of Local Structure and Analysis of Jetting Performance of Main Nozzle in an Air-Jet Loom,TS103.337.1
  4. Study of the Coal Washing Product Structure Optimization,TD94
  5. Chongqing agriculture in the context of urban and rural industrial structure optimization,F327
  6. Investigation of Plasma Sprayed NiCr-Cr3C2 Coating on Mould CrZrCu Alloy Plates,TG174.442
  7. Improvement and Optimization of Pulse Continuously Variator Commission,TH132.46
  8. Research on the Spatial Structure Optimization Model of A County Tourism Based on System Theory,F592.7
  9. Liaocheng Optimization of Local Fiscal Expenditure Structure,F812.45
  10. Analysis and Evaluation of Some Heavy Truck Drive Axle Housing’s Static and Dynamic Characteristics,U463.218.5
  11. The Research on the Optimizing the Ski Tourism Industry Structure at Chongli in Hebei Provinc,G863.1
  12. FEM Analysis and Structure Optimization of Electrode of Hot-pressing Reflow Soldering,TG407
  13. Perspective of Regional Integration Research on Optimization of Spatial Structure in Changchun City,TU984.113
  14. Study on the System of Spatial Structure of Tourism in Liaoning Province,F592.7
  15. Preparation and Luminous Property of Tm and Dy Doped YSZ Coating,TG174.442
  16. Stainless steel industrial optimization and development mode of,F224
  17. The Research of Industrial Structure Optimization Based on China’s Transformation of Economic Development Pattern,F121.3
  18. Preparation and Characterization of W Coatings Prepared by Low Pressure Plasma Spraying,TG174.44
  19. Study on the Strategy of Upgrading of Shanghai’s Industrial Structure,F127
  20. Analysis and Optimization Design of Electric Spindle Based on Stiffness Calculation of Ball Bearing,TH133.3
  21. Numerical Study of Heat Transfer Performance of Rectangular Finned Elliptical Tube Heat Exchanger,TQ051.5

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > Metal corrosion protection,metal surface treatment > Corrosion control and protection > Metal surface protection technology
© 2012 www.DissertationTopic.Net  Mobile