Dissertation > Excellent graduate degree dissertation topics show

Study on Coating Thickness Inhomogeneity of Cold Rolling Hot-dip Galvanizing Sheet

Author: CuiQiPeng
Tutor: ZhaoHongYangï¼›WangJunSheng
School: Liaoning University of Science and Technology
Course: Materials Processing Engineering
Keywords: hot-dip galvanizing air knife numerical simulation coating thickness pressure distribution
CLC: TG174.443
Type: Master's thesis
Year: 2012
Downloads: 113
Quote: 0
Read: Download Dissertation

Abstract


Galvanized sheet is coated with a layer of zinc on its surface, which has many advantages including excellent corrosion resistance, good forming property, low cost as well as good appearance. During galvanizing edge over coating (EOC) may occur near the edge of the strip, which not only causes the waste of zinc but also brings about serious effect on following processes. In hot-dip galvanizing process, liquid zinc was wiped off by the high speed jet flow generated by air knife, so air jet wiping control is so crucial part to determine the coating thickness and uniformity of the zinc layer on the strip.The main purpose of this thesis is to study the influence factors on the coating thickness inhomogeneity of cold rolling hot-dip galvanizing sheet with numerical simulation combined with laboratory experiments. The distributions of static pressure and shear pressure on the strip were calculated by Fluent numerical simulation software, and the influences of air knife at the different conditions were discussed. Meanwhile the actual pressure on the strip and coating thickness were measured by laboratory method,the distribution principles were investigated and the results between simulations and experiments were compared.The main content of this thesis includes three parts:The distribution of coating thickness on the steel strip is measured and observed by optical microscope, SEM and AFM to find the principle of distribution along the width of strip in the first part.The influences of the jet nozzle pressure, the nozzle to strip distance, the nozzle slit opening, the edge baffle plate of air knife, as well as the tilting angle of air knife under the different conditions were discussed. Furthermore, the distribution of zinc on the surface of steel strip in jet wiping process is simulated by Fluent software in the second part.The distribution of pressure along the width of the strip is measured by pressure sensors in the laboratory. A simulated device that refers to the real equipment has been made for studying the distribution of zinc by the function of air-knife jet wiping. And the results from simulations and experiments are compared in the third part.

Related Dissertations

  1. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  2. Study on Springback of High-Strength Steel Stamping,TG386
  3. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  4. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  5. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  6. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  7. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  8. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  9. Numerical Simulation of SNCR Process of a 600MW Utility Boiler,TK222
  10. Numerical Simulation of Biomass Direct Reburning,TK16
  11. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  12. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  13. Study on Gas-Solid Two-Phase Flow in Spouted Beds,TK173
  14. Experimental Study and Numerical Simulation on Aerodynamic Field of Tangential Bias Swirl Burner,TK223.23
  15. Characteristic Study of Combustion in Central Reverse Flame Chamber,TK223.21
  16. Numerical Simulation and Contrastive Analysis of Labyrinth Seals and Leaf Seals,TK263.2
  17. Numerical Study on Phosphorus Distribution in Water Environment of the Three Gorges Reservoir,X832
  18. The Design and Performance Simulation of External Valve Small Displacement Pump,TE933.3
  19. Analysis of the Impact of Tailings Dam Stability under Seepage Role,TV649
  20. Adult OSAHS Preoperative and Postoperative Nasal and Pharynx Cavity and Soft Palate of the Numerical Analysis of Fluid-structure Interaction,R766
  21. Multilayer coextrusion drooling forming process temperature control technology,TQ320.721

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > Metal corrosion protection,metal surface treatment > Corrosion control and protection > Metal surface protection technology > Metal complex layer of protection > Hot dip
© 2012 www.DissertationTopic.Net  Mobile