Dissertation > Excellent graduate degree dissertation topics show

Study of Temperature Compensation of Selective Laser Sintering Processing Based on Temperature Field

Author: RuanYaoBo
Tutor: DongXingTao
School: Zhejiang University of Technology
Course: Mechanical Manufacturing and Automation
Keywords: selective laser sintering (SLS) preheating temperature temperature compensation
CLC: TF124.5
Type: Master's thesis
Year: 2009
Downloads: 14
Quote: 0
Read: Download Dissertation

Abstract


Selective laser sintering (SLS) is one kind of rapid prototyping technologies, which sinters powdery material selectively to produce three-dimensional mechanical parts. During the manufacturing period of SLS, the preheating temperature is one of the most important factors that will affect the mechanical property of the products. Because the preheating temperature field of the powder bed surface is not uniform, the mechanical property of parts sintered in different area is very different. Temperature compensation study at low-temperature regions by increase heat sources in the powder bed surface at the basic research of preheat temperature field of powder bed. The study has important practical significance in enhance the mechanical properties and accuracy of selective laser sintering parts.First, Analysis of the SLS preheating mode and preheating heat transfer process. Calculation the heat flux of surface of powder bed which under thermal radiation. Analysis preheat devices and thermal radiation properties. A physical model for the steady-state preheating heat transfer of powder bed is established.Based on the physical model for the steady-state preheating heat transfer, the steady-state preheating temperature field of the powder bed surface is analyzed by finite-element method. And further research the selective laser sintering steady state temperature field which have point, line, box-type heat. Found that temperature compensation by increase heat in powder bed can significantly improve the temperature field. So as to avoid the situation that of insufficient strength and warp of parts due to preheat temperature is not high enough.At the basis of theoretical analysis, powder bed temperature compensation by add the heat source at the edge of the region is Proposed. The weight of the sample is used to measure the effect of temperature compensation. The optimum parameters of temperature compensation are studied by orthogonal design. Study the relationship between process factors and the effect of temperature compensation.

Related Dissertations

  1. Temperature Compensation and Auto-calibration of High-Precision Electronic Balance,TP274
  2. Hot wire TIG hot wire welding temperature analysis and simulation of temperature field,TG422.3
  3. Micro inertial resistance to magnetic interference and temperature compensation method,V249.322
  4. Research of the Temperature Drift Compensation Method of Piezoresistive Pressure Sensor,TH812
  5. Research on Electronic Unit of Intelligent Metal Tube Rotameter,TH814
  6. Intelligent Design of Temperature Compensation of Pressure Sensor Based on MEMS,TP212
  7. The Performance Study on Low-pressure Water Hydraulic Throttle Valve with Piezoelectric Actuator,TH137.5
  8. Regulation of laser cladding Experimental Study of Cracking Behavior,TG174.44
  9. Analysis and Study on the Test of Motor Vehicle Exhaust Discharge,U467.48
  10. High-power commercial induction cooker control solutions,TM925.5
  11. Intelligent processing of multiple sensor signals,TP212
  12. Study on Methods of Sensor Signal Processing,TP14
  13. The Microcomputer Compensated Crystal Oscillator,TN752
  14. A Temperature and Process Compensated Ring Oscillator,TN752
  15. Error Modeling and Compensation of Micro Inertial Measurement Unit,V241.5
  16. Research on Long-period Fiber Gratting Used in Structural Health Monitoring,TN253
  17. Research on Intelligent Flow Measure Instrument&System Based on LonWorks Bus,TP216
  18. The Design of Intelligent Field Temperature Calibrator,TH811
  19. Research and Implementation of Error Calibration and Temperature-induced-error Compensation Technique for the FOG IMU,V241.5
  20. Research of White LED Driver IC with Ambient Temperature Compensation Technology,TN312.8

CLC: > Industrial Technology > Metallurgical Industry > Metallurgical Technology > Powder metallurgy (metal ceramic technology ) > Powder molding, sintering and post-processing > Sintering process
© 2012 www.DissertationTopic.Net  Mobile