Dissertation > Excellent graduate degree dissertation topics show

Design and Simulation of Pressure Casting Process for Magnesium Steering Wheel

Author: HanJian
Tutor: YuXinQi;WangAiLin
School: Hebei University of Science and Technology
Course: Mechanical Engineering
Keywords: Magnesium alloy Steering wheel Die-casting Orthogonal test Flow-3D Casting parameters
CLC: TG249.2
Type: Master's thesis
Year: 2010
Downloads: 85
Quote: 0
Read: Download Dissertation


UG software based on magnesium alloy automotive steering wheel die casting process analysis , according to the design principles of the gating system design the top NOTE casting system , ring casting system and side NOTE casting system three gating system . Flow-3D software simulation times three gating system temperature field, flow field and defects analysis , the final results showed that the top casting casting system optimal . Die casting process parameters on the basis of determining the magnesium alloy automotive steering wheel skeleton gating system , in accordance with the principle of orthogonal experiment method , the packet ; Flow-3D software simulation parameters of the programs , each flow field the temperature field and the defect distribution in Fig . Identified through the analysis of simulation results , the influence of the casting process parameters of the forming process of the product , and to determine the design of the products forming the optimal process parameters : injection speed of 3m / s, preheating temperature of 400K, the casting temperature 925K and injection speed of 5m / s, preheating temperature of 400K, the casting temperature of 925K .

Related Dissertations

  1. Microstructure and Mechanical Properties of Mg-Zn-Y-Zr Alloys,TG146.22
  2. Powered Activited Carbon-UF for Treating Micro-polluted Surface Water,X703
  3. Process Optimization and Degradation Kinetics for Microwave Vacuum Drying of Different Traditional Chinese Medicine Extract,TQ461
  4. Study on Extracting Process of Rhizoma Alismatis and Rhizoma Smilacis Glabrae and Their Hypouricemic Effects,R284
  5. The Research of Synthesis of Bisphenol-A Polycarbonate Through Melt Transesterification Process,TQ323.41
  6. Applied Research of Emulsified Fuel on S195 Diesel Engine,TE626.24
  7. Investigation of Plasma Sprayed NiCr-Cr3C2 Coating on Mould CrZrCu Alloy Plates,TG174.442
  8. The Research on Extrusion Parameters Through the Plate Billet of Magnesium Alloy,TG379
  9. Research on Aqueous Emulsion Releasing Agent for Aluminum Alloy Die Casting,TQ630.7
  10. Rolled Mg-Zn-Ce-Zr (Mn) alloy microstructure and mechanical properties of,TG339
  11. Repeated upsetting suppress Mg-Si alloys prepared microstructure and properties,TG146.22
  12. Dissimilar magnesium alloy AZ31 and NZ30K study of laser welding,TG456.7
  13. Mg-Al-Mn (-RE) die-cast magnesium alloy Low Cycle Fatigue Behavior,TG136.1
  14. Magnesium alloy cylinder casting process and simulation analysis,TG292
  15. ECAP for Mg-Zn-Zr-Gd alloy fatigue behavior of,TG379
  16. Longitudinal magnesium alloy AZ91 under AC magnetic field properties of welded joints,TG407
  17. Magnesium alloys and corrosion resistance of phosphating process,TG174.4
  18. Plastic deformation on direct smelting crude magnesium AZ91 magnesium alloy and hardness of,TG146.22
  19. Si-containing magnesium alloy microstructure and mechanical properties,TG146.22
  20. Die-cast magnesium alloy automotive steering column bracket CAE,TG249.2
  21. Vacuum casting AZ91 Magnesium Alloy Corrosion Resistance,TG146.22

CLC: > Industrial Technology > Metallurgy and Metal Craft > Casting > Special Casting > Pressure die casting
© 2012 www.DissertationTopic.Net  Mobile