Dissertation > Excellent graduate degree dissertation topics show

Study on Laser Cladding Nickel Based Alloy and Nano-composite Coatings

Author: ZhangShiHong
Tutor: LiMingXi
School: Anhui University of
Course: Materials Processing Engineering
Keywords: Laser cladding nano-CeO2/Sm2O3 microstructure properties numerical simulation
CLC: TG174.4
Type: Master's thesis
Year: 2007
Downloads: 50
Quote: 0
Read: Download Dissertation

Abstract


Nano & Micro CeO2 or Sm2O3/Ni-based alloy coatings, deposited on low carbon steel substrate by laser cladding are introduced. Cross-sections of single track and multi-track, single and multi-layer of the coatings have been examined to reveal microstructure and phase composition using optical microscope, scanning electron microscope （SEM, including EDS microanalysis） and X-ray diffraction instrument （XRD）. Microhardness profile, electrochemical corrosion and wear resistance of the coatings were also tested. The 3D finite element models were set up for the coatings with the theories of elastic-plastic deformation and nonlinear transient heat transfer. The temperature and stress field of Ni-based alloy coating were simulated by the MSC. Marc 2005 non-linearity finite element software.The results showed that smooth coatings were prepared with proper processing parameters （P=2.0 kW, V=180 mm/min） by adding 1.5% nano-CeO2.Homogeneous distribution of alloy elements and microstructure was obtained by mechanically grinding the mixture of nano-CeO2/ Sm2O3 and Ni-based alloy powder. There were primary phaseγ-Ni, Cr23C6 and Ni3B in Ni-based alloy coatings. CeNi5 appeared with nano-CeO2 addition, and Fe7Sm, Ni3Si existed in Sm2O3/Ni-based alloy coatings. Directional solidification of dendrite was found at the interface in 1.5% micro-CeO2 / Ni-based alloy coatings, whereas fine and multi-orientation growth of dendrite appeared in 1.5% nano-CeO2 / Ni-based alloy coatings. Finer and actinomorphous dendrite was found at the interface by adding 3% nano-CeO2. At the bonding area of 1.5% Sm2O3/Ni-based alloy coatings, dendrite growth was observed by adding micro powders where equiaxed dendrite was shown with nano powder addition. With rare earth oxide powder addition, the width of the metallurgical bonding was smaller than that of Ni-based alloy coatings.The hardness and wear resistance of the coatings were improved greatly with nano-CeO2 addition. With increase amount of powder, the mechanism of wear was found from adhesive wear to abrasive wear. In acid corrosion solution, extractive corrosion was found in Ni-based alloy coatings and micro-CeO2/ Ni-based alloy coatings, but uniform corrosion in nano-CeO2/ Ni-based alloy coatings. The corrosion resistance was greatly improved with 1.5 % nano-CeO2 addition. Compared with the coatings with nano-CeO2 addition, the microhardness and wear resistance decreased but the corrosion velocity increased in the coatings with nano-Sm2O3 addition.The simulation results showed that with same laser power density, the mean stress in the coatings decreased by reducing laser scanning speed. Stress concentration area and average value of the thermal stress in the coatings could be effectively reduced by preheating the substrate, controlling time interval between tracks and adjusting scanning path. Cracks produced at the beginning of the second track by stress concentration which direction was 45°angle to that of laser scanning speed.

Related Dissertations

  1. A Research on Factors of the Establishment American Family Properties Decalaration System,D771.2
  2. The Preparation and Thermoelectric Properties of Rare Earth Subsituted Ag Composite Ca3Co4O9-Based Oxides,TQ174.1
  3. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  4. Synthesis, Structure and Properties of PBO/SWNT Composite Fibres,TQ340.64
  5. Preparation and Tribological Properties of TZ3Y20A-SrSO4 Ceramic Matrix Composites,TB332
  6. Reactive Hot-Pressing and Mechanical Properties of （ZrB2-ZrO2）/BN Composites,TB332
  7. Research on Welding Characteristics of CO2 Laser-GMA Hybrid Welding for Ultra-Low Carbon Bainitic Steel,TG456.7
  8. Microstructure and Mechanical Properties of Mg-Zn-Y-Zr Alloys,TG146.22
  9. Investigation on Microstructure and Properties of Cadmium-Free Silver-Based Intermediate Temperature Filler Metals,TG425.2
  10. Study on Springback of High-Strength Steel Stamping,TG386
  11. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  12. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  13. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  14. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  15. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  16. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  17. Numerical Simulation of SNCR Process of a 600MW Utility Boiler,TK222
  18. Numerical Simulation of Biomass Direct Reburning,TK16
  19. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  20. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  21. Study on Gas-Solid Two-Phase Flow in Spouted Beds,TK173

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metallurgy and Heat Treatment > Metal corrosion protection,metal surface treatment > Corrosion control and protection > Metal surface protection technology
© 2012 www.DissertationTopic.Net  Mobile