Dissertation > Excellent graduate degree dissertation topics show

Study on Preparation Process and Properties of Ceramic Corundum Abrasives

Author: LiWenXue
Tutor: LiZhiHong
School: Tianjin University
Course: Materials Science
Keywords: Ceramic corundum Abrasives Preparation process Properties
CLC: TG73
Type: Master's thesis
Year: 2007
Downloads: 86
Quote: 2
Read: Download Dissertation

Abstract


In the preparation process of ceramic corundum abrasives, the effects of the initial concentration of raw materials, the adding methods of the ammonia, ball milling time, different additives and their composition, addition amount and sintering temperature on the microstructure, single particle compressive strength of the abrasives were researched systematically via scanning electronic microscope (SEM) and diamond single particle compressive strength tester.The results showed that the properties of the abrasives were influenced remarkably by the initial concentration of the materials, the ball milling time, the adding methods of ammonia, additives and their composition, addition amount and sintering temperature. With the increase of the initial concentration of raw materials, the grain size of abrasives increased, but the abrasive’s single particle compressive strength reduced. The excessive adding speed of the ammonia would induce the rapid growth of abrasive grains, the poor compactness of the abrasives and the decline of single particle compressive strength. Longer ball milling time didn’t consequentially result in better properties of abrasives, proper ball milling time would not only improve the properties of abrasives, but increase the production efficiency. The grain size could be controlled effectively and the compactness of the abrasives would be improved greatly by choosing suitable additives. Proper additives composition would promote the sintering of alumina, restrain the growth of grains and improve the single particle compressive strength of abrasives. The grains could be fined and the single particle compressive strength of abrasives could be increased by adding appropriate amount of additives. Sintering temperature had obvious effect on the properties of the abrasives, the better properties of alumina abrasives could be obtained at appropriate sintering temperature.

Related Dissertations

  1. The Preparation and Thermoelectric Properties of Rare Earth Subsituted Ag Composite Ca3Co4O9-Based Oxides,TQ174.1
  2. Synthesis, Structure and Properties of PBO/SWNT Composite Fibres,TQ340.64
  3. Preparation and Tribological Properties of TZ3Y20A-SrSO4 Ceramic Matrix Composites,TB332
  4. Reactive Hot-Pressing and Mechanical Properties of （ZrB2-ZrO2）/BN Composites,TB332
  5. Research on Welding Characteristics of CO2 Laser-GMA Hybrid Welding for Ultra-Low Carbon Bainitic Steel,TG456.7
  6. Microstructure and Mechanical Properties of Mg-Zn-Y-Zr Alloys,TG146.22
  7. Simulation and Experimental Study on the Scattering Properties of Two Dimensional Rough Surfaces,TP391.41
  8. Urothermal Synthesis, Structure and Characterization of Functional Coordination Polymers,O631.3
  9. Purification of Endogenous Proteases from (Litopenaeus Vannamei) Shrimp Head and Their Enzymology Properties,S985.21
  10. Rock-fill Concrete Experiments on Comprehensive Properties and Studies on Thermal Stress,TU528
  11. Study on Preparation and Properties of Protein Isolates from Tilapia,TS254.4
  12. Study on the Recycling of Post-Consumer Polyester Textiles,X791
  13. Fabricationand Properties of SiC-AlN Multiphase Ceramics Prepared by Gelcasting,TQ174.62
  14. Flexible,rigid,Synthesis and characterization of mixed ligand complexes,O621.1
  15. Synthesis of Polysulfones and Modification for Epoxy Adhesives,TQ433.437
  16. The Study on the Creep Resistance Property of Ultra-High Molecular Weight Polyethylene Fiber,TQ342.61
  17. Modification and Application of the Waste Fluorgypsum and the Treating of High Concentrations Fluoride Wastewater,X703
  18. Soil Eoclogical Risk Evaluation of Transgenic Bt Rice Through Nematode Community Analysis,S154.1
  19. Preliminary Study on Obstacles Effect of Succession Cropping and Reduction Techniques of Microbial Agents in Flue-cured Tobacco,S572
  20. Expression of Glucose Oxidase Gene from Aspergillus Niger Z-25 in Pichia Pastoris,Q78
  21. Study on Technics & Performance of Nano Electroless Composite Plating on 20~# Steel,TQ153

CLC: > Industrial Technology > Metallurgy and Metal Craft > Cutting tools, abrasives,abrasive tools,fixtures,molds and hand tools > Abrasive
© 2012 www.DissertationTopic.Net  Mobile