Dissertation > Excellent graduate degree dissertation topics show

Intelligent Control System Based on Fuzzy Control Technology

Author: YuChengSen
Tutor: WuGuoZhong´╝ŤLiangNing
School: Zhejiang University
Course: Electrical Engineering
Keywords: Automatic grouting system Fuzzy PID Pressure sensor Embedded Systems
CLC: TP273.4
Type: Master's thesis
Year: 2008
Downloads: 117
Quote: 0
Read: Download Dissertation


With the increasing requirements of modern grouting , grouting automatic control system of high-performance increasingly urgent demands . Automatic Filling control system constituted by the sensor, controller , piston pump and the throttle , and complex control in order to achieve the flow and pressure of the filling hole slurry injected into the system by adjusting the the plunger pump rotational speed and the throttle opening degree . Because the the grouting system itself large inertia lags , slurry flow rate and pressure of the grouting hole and there is strong coupling relationship , so make the slurry grouting hole pressure is always to meet the the grouting design requirements very difficult . This article describes the automatic filling system work , and Water Resources and Hydropower Engineering , discusses the background of the application of the automatic filling system , domestic and foreign research status and technology trends ; propose a high-performance smart grouting control the overall design of the system and control system in the main part of its characteristics ; major analysis of the grouting system pressure , flow rate variation and its impact on the requirements of the sensor system is proposed to adapt to the physical parameters of grout holes slurry detection sensor design structure and acquisition accuracy ; study on the the grouting system 's pressure - flow coupling control algorithm , on the basis of analysis of the inflow the grout holes slurry pressure - flow coupling model proposed for based on fuzzy PID control algorithm ; use in the harsh the grouting environment under the controller hardware design , the use of a distributed control system to meet the requirements of the grouting system , on-site data acquisition and real-time control by the master controller of the built-in memory , hand-held control by a S3C2440 multimedia processor monitoring data and run the set , the CAN network connection between two modules for data exchange ; experimental test of the control system , and summarizes the research experience and development direction for further research .

Related Dissertations

  1. Research on Temprature Controling Technology of Laser Diode with Thermoelectric Cooler,TN248.4
  2. Research on Temperature Control System for Laser Diode,TP273
  3. Borehole imaging device based on embedded systems research,P634.3
  4. Research on Modification and Application of Particle Swarm Optimization Algorithm Based on Control Methods,TP301.6
  5. A Project about Intergrative Control System of Elevator Drive and Power Feedback,TP273
  6. Design and implementation of the multi-channel pressure sensor auto-calibration system,TP212
  7. The Wireless Virtual Storage System Based on WiFi,TN929.5
  8. Study on Instrument Calibrator for Diesel Engines and Its Integrated Information Management System,TK426
  9. Development of Smart Sensor Network System Based on CAN Bus,TN929.5
  10. The Design of a New ARM Experimental Device Which Bases on Chip of S3C2410A,TP368.1
  11. Research on Porting of Embedded TCP/IP Stack TINET,TP368.1
  12. Research and Implementation of Embedded Network Video Software,TP393.09
  13. Research of Automatic Code Generation Technique for Embedded System Graphic User Interface,TP368.1
  14. OLED graphical interface and button design,TP368.1
  15. TD-SCDMA wireless network performance monitoring terminal design and implementation,TN929.533
  16. High-speed transmission for lossless video embedded Gigabit Ethernet Access Technology,TN915.6
  17. Embedded video decoder motion compensation process data layout optimization,TN919.81
  18. JTAG-based ARM11 debugging software design and implementation,TP332
  19. Based on Embedded Technology patch clamp data acquisition system hardware design,TP274.2
  20. Heavy duty gas turbine control system analysis and application,TK323
  21. SOC platform for advanced control design and implementation,TP273

CLC: > Industrial Technology > Automation technology,computer technology > Automation technology and equipment > Automation systems > Automatic control,automatic control system > Fuzzy control, fuzzy control system
© 2012 www.DissertationTopic.Net  Mobile