Dissertation > Excellent graduate degree dissertation topics show

Numerical Simulation of Residual Stress and Shrinkage after Ejection for Injection Molded Parts

Author: LiuHeng
Tutor: ShenChangYuï¼›CaoWei
School: Zhengzhou University
Course: Materials Processing Engineering
Keywords: Shrinkage Residual stresses Injection molding Numerical simulation
CLC: TQ320.662
Type: Master's thesis
Year: 2011
Downloads: 88
Quote: 0
Read: Download Dissertation

Abstract


With the rapid development of injection-molded parts in different fields, products are usually requested to have high precision and complicated shapes. However, defects affect performance of parts. To reduce the cost and time, it is important to measure and simulate residual stresses and shrinkage of the injection-molded parts. There are evidences indicating that the residual stress and shrinkage is produced due to pressure, temperature change etc. during packing and cooling stage. In this study, the numerical analysis of residual stresses produced during the packing and cooling stage of injection molding and shrinkage after ejection was carried out. The major work and main conclusions are as following:1. Based on the fluid mechanics and flow characteristics of polymer melt in cavity, using time-temperature equivalence, the reasonable simplification and hypothesis were introduced. The mathematical model of residual stresses produced during the packing and cooling stages of injection molding was established.2. In order to verify the numerical results obtained from the developed program, the simulation results were compared with the experimental data for PS. The residual stress of parts during packing and cooling stages was analyzed by changing the process conditions. The results showed that as the packing pressure increases, in-plane residual stresses becomes large, the width of the central parabolic portions in the residual stress profile increases with the mold temperature, the injection velocity and melt temperatures nearly has no effect on residual stresses.3. The mathematical model of shrinkage was established and shrinkage of the injection molded parts was analyzed for PS. The shrinkage decreases as the packing pressure, mold temperature and melt temperature increase. Injection velocity nearly has no effect on shrinkage. The results showed that the predicted shrinkage was found to be reasonable to describe the effects of processing conditions well.

Related Dissertations

  1. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  2. Study on Springback of High-Strength Steel Stamping,TG386
  3. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  4. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  5. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  6. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  7. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  8. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  9. Numerical Simulation of SNCR Process of a 600MW Utility Boiler,TK222
  10. Numerical Simulation of Biomass Direct Reburning,TK16
  11. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  12. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  13. Study on Gas-Solid Two-Phase Flow in Spouted Beds,TK173
  14. Experimental Study and Numerical Simulation on Aerodynamic Field of Tangential Bias Swirl Burner,TK223.23
  15. Characteristic Study of Combustion in Central Reverse Flame Chamber,TK223.21
  16. Numerical Simulation and Contrastive Analysis of Labyrinth Seals and Leaf Seals,TK263.2
  17. Voice Signal De-noise Base on Wavelet and Arithmetic Implement with DSP,TN912.3
  18. Rock-fill Concrete Experiments on Comprehensive Properties and Studies on Thermal Stress,TU528
  19. Numerical Study on Phosphorus Distribution in Water Environment of the Three Gorges Reservoir,X832
  20. The Design and Performance Simulation of External Valve Small Displacement Pump,TE933.3
  21. Analysis of the Impact of Tailings Dam Stability under Seepage Role,TV649

CLC: > Industrial Technology > Chemical Industry > Synthetic resins and plastics industry > General issues > Production process and production technology > Forming > Injection molding
© 2012 www.DissertationTopic.Net  Mobile