Dissertation > Excellent graduate degree dissertation topics show

The shaped charge inversion charge structure

Author: HanDongMei
Tutor: HuangZhengXiang
School: Nanjing University of Technology and Engineering
Course: Weapons systems and the use of engineering
Keywords: Inverse design Shaped charge design Inverse design of cone liner
CLC: TJ410.52
Type: Master's thesis
Year: 2012
Downloads: 82
Quote: 1
Read: Download Dissertation

Abstract


As the application of shaped charge is coming into wider and wider use, the request for jet’s penetrating target is not just a single object any more. For instance, when jet is used to penetrate geotechnical for oil, the penetration hole should be in proper depth and no blocking by pestle; when the structure of shaped charge locates at the preceding part of the tandem warhead, in order to ensure that the warhead behind could follow successfully, the shaped charge is required to be able to not only penetrate deep but also drill large hole. Since different jets have different penetrating power to the object, the shaped charge should be designed in accordance with their application requirement.The designing method of shaped charge in common use at present could be concluded mainly as follows, the first step is choosing the structure of shaped charge according to experience, then taking numerical simulation to the structure, when the simulation results are close to the technology index of tactics, experiments should be taken to verify whether the results meet the requirements, if not, the structure of shaped charge should be adjusted. The period of this kind of designing method is too long, the designers are required to be highly experienced, so this method is not used longer.This inverse design method is based on the jet shaped theory, using genetic algorithm, to optimize the shaped charge design. Inversion calculation is used in this text to design the structure of shaped charge, which is in accordance with penetrating target in this method, the jet parameters are taken as input, while the medicine-type cover geometric parameters are output. The calculation is fast, the experience required is not much, and ideal medicine-type cover parameters could be obtained through just a few adjustments.The structure of shaped charge resulting from inversion calculation is tested through AUTODYN simulation software and experiment.The simulation results show that after the medicine-type cover obtained from inversion design is crush molded, the deviation between the velocity of the jet’s preceding part, the effective jet conversion rate and the target value is less than 15%. therefore, the inversion designing is considered to be able to direct the engineering design of the structure of shaped charge effectively.

Related Dissertations

  1. Research on Design Method for Rotor Airfoils Based on Navier-Stokes Equations,V275.1
  2. Fast Airfoil Design Based on Gaussian Process Regression,V224
  3. Study on Decentralized Adaptive Backstepping Control for Reconfigurable and Modular Robots,TP242
  4. Fault-tolerant Control for Reconfigurable and Modular Robots Based on Local Information,TP242
  5. Research on Aerodynamic Design Method for Helicopter Rotor Airfoils,V211.52
  6. Inverse Design of Supersonic Internal Flow Path Based on Given Outflow Velocity Profile,V231
  7. Kinematic Analysis of Plannar Cam Mechanism Based Assur-group Method and the Development of Computer Aided Reverse Design System,TH112
  8. Airfoil inverse design method based on the goal pressure distribution optimization .,V224
  9. Reverse Kinematics Design and Experimental Verification of Weft Insertion Mechanism with Free Pitch Curve of Non-circular Gear,TH132.41
  10. Investigation on Spectral Properties of Rough Surface and the Inverse Problem,O433.4
  11. An Intelligent Design Technology of Alleviated Thermal Stress FGMs,TB34
  12. Research on Inverse Design Method of Structure and Its Application in Engineering,TH122
  13. Unsteady Flow Analysis and Inverse Design of Airfoils Via a New Variable-Domain Variational Space-Time Finite Element Method,TH122
  14. Research on Image Recognition Technology of Mechanical Product and Its Application in Reverse Design,TH122
  15. Study of Dynamic Inverse Design Method on Impact Machines,TH122
  16. Research of Adaptive Meshfree and Hybridized Mesh/Meshfree Methods,TP391.41
  17. Research on the Distributed Parameter Modelling and Control Method of Manipulators Handling a Flexible Payload,TP241
  18. Reverse Design of Swing Roller Dish Cam-follower and Auto-creating of the Cam CNC Code,TH112.2
  19. Research of Automatic Ammunition Packing Equipment,TJ410.52
  20. Penetration Research of Shaped Charge into Typical Soil/Concrete Target,TJ410.52
  21. Study on Linear Charging Technology and Property with SY Primary Explosive,TJ410.52
  22. Mechanism Study of Muti-mode Shaped Charge in Point-Ring Ignition,TJ410.52

CLC: > Industrial Technology > Arms industry > Ammunition, fuses, pyrotechnics > Ammunition > General issues > Manufacturing processes and equipment > Charge process and its equipment
© 2012 www.DissertationTopic.Net  Mobile