Dissertation > Excellent graduate degree dissertation topics show

Application of a Novel Cationic light curing system

Author: ZhangMing
Tutor: NiXiuYuan
School: Fudan University
Course: Chemical Engineering
Keywords: UV curing cationic polymerization diaryliodonium salt touch panel lab shear Shrinkage comformal coating Salt fog
CLC: TQ630.1
Type: Master's thesis
Year: 2011
Downloads: 198
Quote: 0
Read: Download Dissertation

Abstract


The UV curing process is a new "Green Technology". The great advantages of UV system are rapid curing speed, high quality coating performance, environmental friendly and low energy consumption. But the inhibition of the oxygen is always a problem for this UV curing technology. While the cationic UV curing process doesn’t have this issue, it brings substantial cost and processing advantages as compared to the competitive UV cure methods based on free radical curing, this new UV curing process will also help on the lower volume shrinkage and better adhesion to the kinds of substrates. In this paper, it was studied that the curing and applications of a novel kind of diaryliodonium salt.Iodonium salts are the most important cationic photoinitiators with efficient photopolymerization. In this paper, [4-(2-hydroxy-3-butoxy-1-propoxy) phenyl]-phenyliodonium hexafluoroantimonate (BPI·SbF6) was studied as the typical catiinic UV agent. Firstly the UV curing process with epoxy resin by BPI·SbF6 system was tested. The curing percentage and properties in different curing phases, also the final cured products properties were studied. At same time, the influence to the coating performance by different curing time was tested and compared with other UV curing system. The results proved BPI·SbF6 had very high reaction ability. Then, two formulations were designed based on this BPI·SbF6 UV system as the optical adhesive and comformal coating applications in electronic industry. For adhesive formulation in touch panel, different components of epoxy resin and active dilution were studied. The curing speed, transmittance, shrinkage, lab shear, also the reliability were compared with other UV products. The results showed these formulations had better performance. For comformal coating formulation, different mixed system with acrylic polymer was designed and the difference of coating performance were tested. Also based on the requirement of electronic industry, the insulation properties, the adhesion to the PCB and the salt fog resistance were tested. The results showed this UV system had very good reliability and fit the electronic protection standards.

Related Dissertations

  1. Voice Signal De-noise Base on Wavelet and Arithmetic Implement with DSP,TN912.3
  2. Research on Software of TFT-LCD Testing Equipment Based on ARM,TN873.93
  3. Rock-fill Concrete Experiments on Comprehensive Properties and Studies on Thermal Stress,TU528
  4. The Experimental Research on Regeneration Aggregate and Proportioning of Recycled Concrete Brick,TU528
  5. The Research of Concrete Shrinkage and Creep Experiment,TU528
  6. Characterization for Crimp Mechanism of PTT/PET Bi-component Filament and Its Fabric Performance,TS101.923
  7. Analyzing of Injection Molding Steel Net Reinforced HDPE Ball Valve by CAE Software,TQ320.662
  8. Synthesis of Modified Epoxy Acrylate Resin and Application as Paper Wet Strength Agent,TS727
  9. Modifed Research of UV Coatings,TQ637
  10. Study on the Properties of PLA Filament and Its Mixed Fabrics,TS101.923
  11. Synthesis and Performance Study on UV-curable Polyurethane Acrylate,TQ630.43
  12. A ship engine room monitoring and alarm system reform and implementation,TP277
  13. Design and Research of the Control System for Rehabilitation Horse,TP273
  14. A Study on Early-age Shrinkage of Concrete and Cement Paste,TU528
  15. Simulation Research on Injection-Compression Molding for Transparent Plastic Panel,TQ320.662
  16. Study on Influence of α-Aminoketone Photo-initiator to UV-heat Dual Curing of Filled Epoxy Acrylate/epoxy Resin System,TQ323.5
  17. The Key Technology Research in Mask Projection Stereolithography,TG665
  18. Research on Image Restoration with Combined Bases,TP391.41
  19. The Research of Car Virtual Instrument System with Linux and ARM,U463.7
  20. The Monomer Compoment and Fillers Microstructure Effect on the Properties of Dental Resin Composites,R783.1
  21. Research on Shrinkage Process of Carbon Steel Cast Ingot,TG142.15

CLC: > Industrial Technology > Chemical Industry > Paint Industry > General issues > Basic theory
© 2012 www.DissertationTopic.Net  Mobile