Dissertation > Excellent graduate degree dissertation topics show

Study on Theory and Experiment of Wire Drawing with Composite Ultrasonic Vibration

Author: XiuXiao
Tutor: XieTao
School: Harbin Institute of Technology
Course: Mechanical and Electronic Engineering
Keywords: composite ultrasonic vibration wire-drawing four-terminal network stress analyze drawing-force surface quality
CLC: TG663
Type: Master's thesis
Year: 2008
Downloads: 47
Quote: 0
Read: Download Dissertation

Abstract


Wire drawing with ultrasonic vibration which belongs to a kind of ultrasonic plastic processing technology is a new processing technology through transferring ultrasonic vibration to common wire drawing. Based on our previous research, this dissertation introduces the factor affecting mentallic plastic transmutation and the basic of mentallic wire drawing. The theory of ultrasonic drawing was studied and experiments was done on the basis of reading and analyzing a large quantity of correlative references .In this dissertation, a study on the effect and influence of composite ultrasonic vibration, axial ultrasonic vibration and radial ultrasonic vibration to wire-drawing is made by the finite element simulating analysis. In the result of the simulation, the stress and wire force and contact friction is emphatically analyzed. Analysis results shows that: the stress and wire force and contact friction of wire-drawing of composite ultrasonic vibration reduce more than axial ultrasonic vibration and radial ultrasonic vibration.Some fundamental four-terminal network matrix and frequency equation are given on the basis of one-dimensional and longitudinal vibration locomotory equation of variable cross-sectional bar. Composite ultrasonic vibration apparatus is designed by the principle and requirements of wire-drawing system with ultrasonic vibrations, the vibration modes and characteristics were analyzed for its correct design. Axial ultrasonic vibration device is also designed for the sake of drawing stainless steel. For the sake of ensuring wire-drawing experiment’s efficiency, vibration measurement of the vibration apparatus is realized by microscope on the base of match analysis of the ultrasonic drive supply and the vibration apparatus, according to whose circuit model impedance is measured by a impedance analyzer.Finally, copper wire-drawing experiment on a practical draw bench LH-200/17 of Harbin cable works were carried out. Wire force is analyzed during the wire-drawing of three kinds of ultrasonic vibration. And stainless steel wire-drawing experiment were carried out for the composite ultrasonic vibration and high-power ultrasonic vibration. The drawing-force value, surface topography and microstructure topography affected by three kinds of ultrasonic vibration are also anlyzed. By qualitative analysis of the experiment, composite ultrasonic vibration can reduce drawing force and prolong the adjusting tensile force cycle more prominently than the other ultrasonic vibration. Ultrasonic vibration can reduce drawing force , improve the quality of the copper-wire and eliminate the condition of broken wires fully.

Related Dissertations

  1. Nuclear Power Plant Steel Milling Surface Integrity Study,TG54
  2. Research on Surface Quality Improvement of Microcellular Foam Injection Molding Parts,TQ320.662
  3. Study and Engineering Application of Self-screwed Slip Casting Tube Bolt in Soft-rock Tunnel Support,U455.7
  4. Based on the track circuit signal transmission technology for heavy freight vehicles,U284.2
  5. Investigation of Material Microstructure on Principles of Manufacturing in Micro-Milling,TG54
  6. Titanium milling tool failure and high surface quality experimental study,TG54
  7. Optimization of Process Parameters in High-speed Milling Inconel 718,TG54
  8. Research on the Key Processing Factors That Influence the Machining of the Fused Silica with Reactive Atmospheric Pressure Plasma,TG664
  9. Study on Machining Mechanism and Surface Quality in Ultrasonic Vibration Grinding of Silicon Nitride Ceramics,TG580.1
  10. Research on Role of Electrolyte in Electrolyte- Plasma Processing Technology,TM912
  11. Study of Vibration and Noise Characteristics Fluid-solid Coupling of the Valve of the Water Pipeline System,TH134
  12. Study on the Characteristic of 304 Stainless Steel Hot Rolling Process,TG335.11
  13. Research on Crankshaft Parameterized FEA System with Rolling Strengthening Effect,TG306
  14. Research on the Ultra-Precision Grinding of Optical Glass Based on Hybrid-Bonded Diamond Wheel,TQ171.684
  15. Nano-Cutting Surface Quality for Single Crystal Silicon and Molecular Dynamics Simulation,TG501
  16. Diamond Fly-Cutting of Microstructured Surface,TG506.6
  17. The Basic Technology Research on the Ultrasonic Milling of CFRP,TG54
  18. Technical Research on Laser Heat Assisted Turning Silicon Nitride,TQ174.6
  19. Research on the Effect of Material Anisotropy on the Machined Surface Quality in Diamond Cutting of KDP Crystals,O786
  20. Based on image processing of the coin surface quality evaluation system design and implementation,TP391.41

CLC: > Industrial Technology > Metallurgy and Metal Craft > Metal cutting and machine tools > Special machine tools and processing > Ultrasonic machining machine tools and processing
© 2012 www.DissertationTopic.Net  Mobile