Dissertation > Excellent graduate degree dissertation topics show

Research and Implementation of EMI Passive Filter in Motor System

Author: LiuXin
Tutor: YangChunLing
School: Harbin Institute of Technology
Course: Electrical Engineering
Keywords: EMI passive filter impedance mismatch CM voltage parasitic parameter coupling
CLC: TN713
Type: Master's thesis
Year: 2007
Downloads: 346
Quote: 2
Read: Download Dissertation

Abstract


The electromagnetic interference (EMI) affects the reliable operation of motor system. This problem should be solved with effective measures. Particularly, using the passive filter is the most effective measure. So EMI passive filter of motor system is composed by mains filter and output side filter.While designing the mains filter, separating EMI into common mode (CM) and differential mode (DM) component is the problem which is should be solved firstly, and also is the difficulty point. The CM spectrum is separated from the interference signal which is measured by LISN in the power supply by DM rejection network composed of three precision resistors. The DM spectrum is calculated with the definition of CM and DM. By the separate results, and the GB4343.1-2003, design the CM and DM circuits of the mains filter. In order to solve the impedances mismatch of mains filter, using the S parameter of the mains filter’s port network, based on the source impedance and the load impedance in actual system, the insertion loss of any operation circumstance can be obtained by calculation. While designing the output side filter, using the common mode equivalent circuit of motor’s coupling parameter, the shaft voltage is reduced to less than the breakdown potential of lubricant film in order to prevent the shaft current. This output side filter takes the motor winding’s inductance and coupling capacitance into consideration, so that the volume and cost are reduced. At the same time, the feedback element is used to deliver the CM current in the motor terminal to the input port of the output side filter. This technique improves the filter’s performance in the aspect of suppressing the shaft voltage.The main reason that affects the filter’s high frequency performance is the passive device’s parasitic parameter and the coupling between them. So that measure should be applied to improve the filter. This dissertation applies PCB plane winding, making use of the negative coupling to suppress the capacitance’s parasitic induction. In order to solve the problem of coupling effect, network analysis method is used to get coupling parameter. Change the winding’s structure and shield the capacitance to reduce the coupling between passive devices. Comparison of experimental results verify that after applying the measure to the system, the high frequency performance of EMI filter is improved greatly, and also verify the availability of the adopted measure.Based on the EMI passive filter’s design principle and method in motor system, as well as the system improvement measure mentioned above, we can design the EMI passive filter which is applied in motor system and can suppress the electromagnetic interference’s disadvantages effectively.

Related Dissertations

  1. Effects of Water and Nitrogen Coupling on the Water and Nitrogen of Soil and Yield and Quality of Flue-cured Tobacco in Luzhou,S572
  2. Effect of Water and Nitrogen Coupling Using on Soil Physical and Chemical Properties in Tobacco Areas and the Yield and Quality of Fule-cured Tobacco in Yibin,S572
  3. Study on Hydraulic Fracturing of Low Permeability Reservoir,P618.13
  4. Nano LaFeO 3 Controllable Synthesis and TiO 2 bridged construct composite photocatalyst,O643.36
  5. Modification of Talc Powder and Its Reinforcing and Toughening on Recycled Polypropylene,TQ325.14
  6. Study on Power System Voltage and Reactive Power Control Method,TM761.1
  7. Construction of High Effective Complex Microbial Community of Aerobic-anaerobic Coupled (AAC) Reactor and Its Treating Ability,X172
  8. Preparation and Studying of RTV-2 Silicone Adhensive for Aircraft,TQ433
  9. Synthetic Methodologies of Functionalized Alkenes, 1,3-dienes and Conjugated Enynes,O623.12
  10. Surface Modification of Natural Barite Powder and Technological Design,TQ630.4
  11. Properties of 1-3 Polymer/Cement Based Piezoelectric Composites,TB332
  12. High-Temperature Magnetic Properties and Mechanism of Exchange-coupling Interaction for FeCo-based Nanocrystalline Alloys,TB383.1
  13. Made of high modulus carbon fiber cyanate ester resin system that matches Research,TB332
  14. Metamaterials and Its’ Numerical Calculations,TB34
  15. Study of the Locked Hydraulic Soft-Start Equipment,TD528.1
  16. Study of Joint Support and Construction of Large Fracture Room in HS Soft Rock,TD354
  17. Aluminum hot extrusion dies dimensional coupled thermal analysis and optimization design,TG375.41
  18. Baogang Cold Plate Leveler Main Drive System Torsional Vibration and Strength Analysis Model,TG333.23
  19. Experimental Research and Umerical Simulation on Shrinkage of Concrete,TU528
  20. Characteristics Analysis and Optimization for the Spindle Unit of High-speed & High-precision CNC Lathe,TG519.1
  21. Research on Electromagnetic Interference of PWM Traction Inverter in Locomotive,TM464

CLC: > Industrial Technology > Radio electronics, telecommunications technology > Basic electronic circuits > Filtering techniques,the filter
© 2012 www.DissertationTopic.Net  Mobile