Dissertation > Excellent graduate degree dissertation topics show

Study of Laser Machining Ceramic Green Bodies

Author: CuiYuanYuan
Tutor: YangJinLong
School: Tsinghua University
Course: Materials Science and Engineering
Keywords: Laser machining Al2O3 ZrO2 Si3N4 SiC
CLC: TQ174.6
Type: Master's thesis
Year: 2010
Downloads: 79
Quote: 0
Read: Download Dissertation

Abstract


Because of good properties on high strength, high hardness, good high temperature performances, abrasion resistant and low density, ceramics have been used widely in all kinds of industrial fields. However, ceramics are extremely hard to molding and machining because of high hardness, brittleness and poor reliability, which hinders their application and development.In this paper, the laser machining performance of the gelcasting green body of Al2O3, ZrO2, Si3N4 and SiC was studied with 3D laser machining. The influence of parameters on the machining quality and efficiency was systematically analyzed, including the laser power, scanning speed, scanning pitch and the solids loading of green body, in order to get optimum parameters.Research found that the machining quality has something to do with the laser power, scanning speed, scanning pitch and the solids loading of green body. For example, both the machining depth and the surface roughness decreased in total with increasing scanning speed. Moreover, with the increase of scanning pitch, the machining depth decreased in total while the surface roughness increased at the same time. The machining depth of Al2O3 and ZrO2 was deeper than Si3N4 and SiC, and it reached a maximum for ZrO2. In addition, nitrogen purging was applied for Si3N4 and SiC, which could obtain a good machining surface and also ensured the machining continuity. When the laser energy density was a bit higher, the crystal grain of pure Al2O3 powder and green body grew up to an orderly pattern after laser machining, and glomeration effect and serious surface sintering were discovered. For the powder and green body of ZrO2, phase transformation of zirconia from tetragonal to monoclinic occurred in accord with the grain growth. Nevertheless, there was no obvious change for the particle size of Si3N4 and SiC in spite that the surface was gasified.Laser machining parameters matched with these four material systems were chosen, which brought the manufacture of the 3D complex-shape parts of ceramics into reality. It is a highly efficient and short-process way for the laser green machining of ceramics to manufacture complex-shape parts. Therefore, it has great theoretical significance and practical value for the structural ceramics with multi-purposes and small quantities.

Related Dissertations

  1. Reactive Hot-Pressing and Mechanical Properties of （ZrB2-ZrO2）/BN Composites,TB332
  2. Fabricationand Properties of SiC-AlN Multiphase Ceramics Prepared by Gelcasting,TQ174.62
  3. Preparation of Epichlorohydrin from Crude Glycerol of Biodiesel By-product,TQ223.26
  4. Nano Pt / SiC Preparation, Characterization and Electrochemical Catalytic Performance,TM911.4
  5. Rsearch on Catalysts Synthesis from 2,2’-Diaminodibenzyl to Iminodibenzyl,TQ463.2
  6. Study on the Catalysts for Hydrorefining of Crude Benzene at Low Temperature,TQ522.62
  7. Effect of Adding ZrO 2 Nanopowder on Microstructure and Mechanical Properties of Carbon Steel,TB383.1
  8. Studies of High Refractive Index Materials Prepared by Nano ZrO2 and TiO2 Hybrid Silicone Epoxy Resin,TB383.1
  9. Preparation and Characterization of Al2O3/C Hybrid Aerogels and Al2O3 Aerogels,O648.17
  10. Preperation of Low Friction and Wear Resistant High-Purity Alumina Ceramic,TQ174.1
  11. Thermal Cycle Stability of SOFC Seal Material,TM911.4
  12. Recrystallized SiC slurry Rheological,TQ174.1
  13. One -dimensional alumina and alumina whiskers Preparation and Characterization,TB383.1
  14. Si 3 N 4 ceramic vacuum brazing process and strengthen joint research,TQ174.6
  15. Precursor Preparation of ZrO 2 -modified C / SiC composite materials and their properties,TB332
  16. Preparation 3DC_f/SiC vapor infiltration of silicon structure, performance and interface Regulation,TB332
  17. 4H-SiC power BJT device simulation and Features,TN303
  18. SIC -oriented MAC protocol for wireless ad hoc network design and implementation,TN929.5
  19. An Atom-Economic Reaction for Synthesis of 1-Phenoxy 2-Propanol Over Al2 O3 /MgO,O643.32
  20. Preparation and Properties of C/SiC Composite Spring,TB332
  21. Processing of SiC_f /SiC Composites Prepared with LPVCS as Precursor Polymer,TB332

CLC: > Industrial Technology > Chemical Industry > Silicate > Ceramic Industry > Production process and equipment
© 2012 www.DissertationTopic.Net  Mobile