Dissertation > Excellent graduate degree dissertation topics show

Research on the MAPPING Technique of Draw Resistivity Isocontours for Sheet Resistance

Author: ZhaoXiaoRan
Tutor: LiuXinFu；ZhangRunLi
School: Hebei University of Technology
Course: Instrument Science and Technology
Keywords: mapping technology sheet resistance four-probe technique
CLC: TM934.1
Type: Master's thesis
Year: 2011
Downloads: 25
Quote: 0
Read: Download Dissertation

Abstract


This paper introduced common methods of micro-resistance test. We choose the four-probe method to study after comparing the merits of each method. The basic principle, measured quasi-conditions, current selection, edge and thickness of the amendment, the choice of measurement region of conventional linear four-probe method was analyzed. Started with the conventional linear four-probe method, the improved Vanderbilt law was introduced, which is also called oblique four-probe method. The measurement principle and test conditions were described, which is better than conventional linear four-probe method. Then the principle of Rymaszewski oblique style square four-probe method for sheet resistivity test was discussed, and the resistivity distribution of 4-inch silicon wafers was determined using this method.The division number and difference of the resistivity was identified and the appropriate threshold was selected from the statistical distribution of resistivity. The resistivity data were attributed to different fuzzy sets according to the fuzzy mathematics theory, the same fuzzy sets corresponding to same resistivity, so the resistance can make the intervals distribution, at last, mapping graph was formed by resistivity graphics drawn with MaTlab software. The express methods selected for mapping diagram are: radial diagram, radial comparison chart, color pictures, gray scale and contour map. Gray scale method, which is determined as the best characterization of sheet resistance for mapping graph by comparing the representation of different sheet resistance graph, was choosen to express the samples test results. The purpose of characterized sheet resistance mapping graph study is to make it clear of the sheet resistance distribution, and increase the analysis effect of test results. This research was intended to improve the representations of the results using original prototype, after the improvement, the representation of results is more intuitive and specific.

Related Dissertations

  1. Research on Operational Life Span and Applications of Coated Electrode Resistance Welding for Galvanized Steel,TG453.9
  2. The Influence of Probe Wanering to Testing Sheet Resistance of Large Silicon and Research on Simulation Technology,TN307
  3. Lead-free solder joints under shear tensile creep resistance strain relations with research,O348.2
  4. The Study on Red Soil Corrosion by the Technological Direct, Continuous Monitoring,X53
  5. Preparation of the Lead-free Silver Conducting Paste for Silicon Solar Cells,TM914.4
  6. Preparation, Microstructure and Photoelectrical Properties of Ag/ITO/Ag Multilayer Films,TB383.2
  7. Preparation and Properties Study of Transparent Conductive ZAO Thin Films,TB383.2
  8. Study on Coated Electrodes in Resistance Spot Welding of Galvanized Steel Sheet,TG453.9
  9. Organic SOL -GEL prepared doped vanadium oxide thin films and Electrical Properties,O484.1
  10. Research on Preparation and Properties of ITO Films,TB383.2
  11. Research on the Modeling of Heart Based on the Virtual Reality Means,TP391.9
  12. Carbon paste printing method and electroless plating Ni-P method produced a preliminary study of embedded resistor technology methods,TN41
  13. Study on Prepared Technology and Properties of ZAOp/ZAO Transparence Conductive Films,TB383.2
  14. Sol - gel technique for preparing ATO powders and thin films , Structure and Properties of,TB383.2
  15. The Research on Conmined Algorithm of PAPR Reduction for MMO-OFDM System,TN919.3
  16. Research on Fabrication and Performance of Mono-crystalline Silicon Solar Cells with High Sheet-resistance Emitter,TM914.4
  17. Synthesis and Properties of Sb-doped SnO2 Thin Film,TB383.2
  18. Fabrication of Ti-O Film by Vacuum Magnetic Filtered Arc Plasma Deposition and Its Blood Compatibility,TB383.2
  19. The Study on Characteristics of ZnO Thin Films Prepared by Magnetron Sputtering,TN304.055
  20. Semiconductor nanocrystals photovoltaic device performance test system,TB383.1
  21. Study on the Al3+-Doped ZnO Thin Films Prepared by Sol-Gel Process,O484.1

CLC: > Industrial Technology > Electrotechnical > Electrical measurement techniques and instruments > Lumped parameter,the distribution parameter measurement and instrumentation > Resistance measurement and instrumentation
© 2012 www.DissertationTopic.Net  Mobile