Dissertation > Excellent graduate degree dissertation topics show

Study on Gas-Solid Two-Phase Flow in Spouted Beds

Author: QianFeng
Tutor: LiuWenTie
School: Harbin Institute of Technology
Course: Thermal Power Engineering
Keywords: spouted bed gas-solid two-phase flow numerical simulation spouted-fluid bed draft tube
CLC: TK173
Type: Master's thesis
Year: 2008
Downloads: 105
Quote: 0
Read: Download Dissertation


Spouted beds are widely used drying equipment in industry. The axial gas flow causes gas-solid two-phase flow with regularity. With the rapid development of hardware and calculation technique, numerical simulation has become an important method to study flow patterns.Euler-Euler two-fluid model is used in this paper, and standard k-εtwo gas-processing model of turbulent flow is applied. Several frictional stress models are introduced to accommodate the instantaneous contact of particles and the half-sustaining contact interaction in the dense zone. Simulations are also carried through on spouted-fluid bed and spouted bed with a draft tube as well.There are three flow zones in spouted bed according to simulation results: the spouted zone with low concentration and high axial velocity of particles; the annulus zone with dense particle flow in low speed and the fountain zone. The simulation result matches the experimental data. Flow parameters such as velocity and temperature of particles are also gained.In spouted-fluid bed, with fluid gas entered from the bottom of inverted cone, the contacts of gas and particle become violent in this area. The fluid gas effects well when enters from normal direction. The introduction of a draft tube causes more distinctness between the flow zones in spouted beds, brings equality to the distributions of particles in each zone. Gas-particle interaction happens mainly inside the drafted tube, and intense two-phase flow also appears around both ends of the tube.

Related Dissertations

  1. The Setting Bases of Working Pressure in LNG Systems and Orthogonal Experiment Design of Heat Exchangers,TQ051.5
  2. Study on Springback of High-Strength Steel Stamping,TG386
  3. Numerical Simulation and Experiment on Hydroforming of Cups with Controllable Radial Pressure,TG386
  4. Research on Technology and Mechanism of Joining Cemented Carbide to Carbon Steel,TG454
  5. Numerical Simulation of Film Cooling in Turbine Cascade with Non-Axisymmetric Endwall Method,V231.3
  6. High Speed Aerodynamic Convection and Coupled Heat Transfer of Complicated Bodies,V215.4
  7. The Analysis on Characteris of Vibration Source about Vertical Vibration of Surrounding Environment Induced by Rail Transit,U211.3
  8. Study on the Heat Transfer Characteristics of Particle Cluster in Circulating Fluidized Bed,TK124
  9. Numerical Simulation of SNCR Process of a 600MW Utility Boiler,TK222
  10. Numerical Simulation of Biomass Direct Reburning,TK16
  11. Numerical Simulation on Pulverized Coal Combustion Process in a 670T/H Tangential Firing Furnace,TK224.11
  12. Numerical Simulation on the Combustion Process in the Furnace of a 1000MW Lignite-Fired USC Boiler,TK224.11
  13. Experimental Study and Numerical Simulation on Aerodynamic Field of Tangential Bias Swirl Burner,TK223.23
  14. Characteristic Study of Combustion in Central Reverse Flame Chamber,TK223.21
  15. Numerical Simulation and Contrastive Analysis of Labyrinth Seals and Leaf Seals,TK263.2
  16. Numerical Study on Phosphorus Distribution in Water Environment of the Three Gorges Reservoir,X832
  17. The Design and Performance Simulation of External Valve Small Displacement Pump,TE933.3
  18. Analysis of the Impact of Tailings Dam Stability under Seepage Role,TV649
  19. Study on Hydraulic Fracturing of Low Permeability Reservoir,P618.13
  20. Numerical Simulation and Experimental Study of Air-Assisted Sprayer of Orchard,S491

CLC: > Industrial Technology > Energy and Power Engineering > Thermal engineering, heat > Industrial thermal equipment > Drying equipment
© 2012 www.DissertationTopic.Net  Mobile